sandman351
07-28-2003, 03:22 AM
Parting out my 351C 4V. Make reasonable offer on any of the following parts:
Holley Strip Dominator, perfect shape, no porting: $425
Closed chamber heads: SS valves, 3 angle valve job, bronze guide liners, mild port and polish, chambers pinned (old oval track trick), hardened exhaust seats, spring seats cut for larger dual springs, has single springs with dampers & spring buckets good to .620 lift, current pressure 120 lbs seat 330 lbs open, 7 degree machined locks and chrome moly retainers, Manley screw in studs and guideplates, shaved to 61cc's, about 20 1/4 mile passes on them, very nice heads, ready to go $750
Moroso chrome valve covers: $50 obo
Cam Research solid flat tappet cam & lifters: 250 int/260 exh dur @ .050" lift, .585/.610 lift, 108 lobe centers, very good cam, ran hard in my cleveland. Will mark lifters. $150 obo
Crane Hardened 5/16" pushrods, stock length: $50 obo
Milodon Roller timing chain, installed new with the heads, 20 1/4 mile passes. $50 obo
Moroso front sump 9 qt pan with pickup, painted black: good shape, not beat up: $175
Short block. Balanced, TRW forged flat top pistons, moly rings, resized and shotpeened stock rods, stock crank turned 10/10, block bored .030 over, decked and align honed, clevite bearings, ARP head and main studs (except at windage tray) and MPG windage tray. Has less than 2000 miles on it. $1000 obo.
All prices fairly negotiable, all reasonable offers will be considered. You pay freight from zipcode 68310. The engine is currently in the car, I hope to get it pulled in the next week or two.
Will also consider trades for a toploader or 460 alum edelbrock
heads.
NEED TO SELL!! MAKE AN OFFER ON MY STUFF!! :)
Email sands@inebraska.com or post here.
Thanks guys!
Pat
Holley Strip Dominator, perfect shape, no porting: $425
Closed chamber heads: SS valves, 3 angle valve job, bronze guide liners, mild port and polish, chambers pinned (old oval track trick), hardened exhaust seats, spring seats cut for larger dual springs, has single springs with dampers & spring buckets good to .620 lift, current pressure 120 lbs seat 330 lbs open, 7 degree machined locks and chrome moly retainers, Manley screw in studs and guideplates, shaved to 61cc's, about 20 1/4 mile passes on them, very nice heads, ready to go $750
Moroso chrome valve covers: $50 obo
Cam Research solid flat tappet cam & lifters: 250 int/260 exh dur @ .050" lift, .585/.610 lift, 108 lobe centers, very good cam, ran hard in my cleveland. Will mark lifters. $150 obo
Crane Hardened 5/16" pushrods, stock length: $50 obo
Milodon Roller timing chain, installed new with the heads, 20 1/4 mile passes. $50 obo
Moroso front sump 9 qt pan with pickup, painted black: good shape, not beat up: $175
Short block. Balanced, TRW forged flat top pistons, moly rings, resized and shotpeened stock rods, stock crank turned 10/10, block bored .030 over, decked and align honed, clevite bearings, ARP head and main studs (except at windage tray) and MPG windage tray. Has less than 2000 miles on it. $1000 obo.
All prices fairly negotiable, all reasonable offers will be considered. You pay freight from zipcode 68310. The engine is currently in the car, I hope to get it pulled in the next week or two.
Will also consider trades for a toploader or 460 alum edelbrock
heads.
NEED TO SELL!! MAKE AN OFFER ON MY STUFF!! :)
Email sands@inebraska.com or post here.
Thanks guys!
Pat