89 lx modd street/strip car ....

[shawnaj7731]

The car is a 89 Mustang Lx orginal v8 car...
I have over 15k in reciepts all work performed by rocketperformance. The car is located in hampton roads (Newport News) VA. The car is no joke and some of the best of the best stuff on it.

engine On motor the car put down 329 RWHP and 330 RWTQ on Spray the The put down 460 RWHP and 475 RWTQ only 150 shot.The car has only 5 passes on the motor the car and the car was just together in the last 3 months everything is basically brand new inside the motor. I have reciepts totaling over 15k into the car all work was done by one shop Called ROCKET PERFORMANCE. The car runs
10:90s consistantly on 150 shot. Car weights 3085 with drive in it. 225 lb drive.and runs 12.50s on motor. THe car pulls the wheels about 2ft off the ground just fyi.
The car is still streetable and is a fun car to drive. Here is a break down there is more probably more just cant think off the head right now picture are below also. ASKING 8800.00 obo or I would be willing to trade it for a nice street bike. Prefer a 1000cc may consider trade and cash too. I miss the sport bike and the wife wont let me have both. So go figure.

slide show

Here is a slide show
http://img208.imageshack.us/slidesho...7605113dp.smil


306 dss complete rotating assembly DSS rotating assembly 306,
Forged Pro Series pistons accomodate both standard inline and Twisted Wedge heads, compression ratios: 54cc, 10.6:1... 58cc, 10.1:1... 60cc, 9.8:1... 62cc, 9.6:1... 64cc, 9.4:1... compression for this motor is 10.1. I thought it was 9.5.1 but spoke to the builder and he said no it has a comp ratio 10.1.1
dss 1.7rr
lSteel SFI Flywheel -
edlebrock victor 5.0 upper and lower intake
edlebrock performer heads 2.02 ported and polished with ferrea valves and stronger springs
Screw in freeze plugs
All ARP hardware was used.
Main Girdle
Cam is Anderson lift 524/544
newer 50oz balance
new undrive pulleys
aluminun radiator with dual electric built in fans
70 mm throttle body with 70 mm spacer
new mac cold air intake
Fms 30lb injector
C&L 80mm mass meter
Aeromotive fuel pressure Regulator
new power steering pump relocated
mellon High volume Oil pump
FMS valve cover New spark plugs, wire etc.
MSD COIL
Hurst Line Lock
new timing chain new water pump and cover
walboro 255lb fuel pump

Transmission
PA C4 built transmission is a Super comp no transbrake,Reverse manual valve body brand new trans cooler and sfi flywheel with a brand new B&M ratch shifter
lines.It has the best of the best inside. 2500 stall

Exhaust
Mac headers 1 5/8
with mac off/rd H pipe
flowmasters with dumps

Rear end
FMS 3.73 with a New just put track lock


Nitrous system a NX Big shot solenoids, kit is complete with
Bottle heater, Purge, Fogger, Pressure Gauge, bottle custom painted.


Suspension
Lakewood 90/10 up front
Moroso Drag springs
Strange Adjustable rear shocks
Moroso drag springs in the rear.
BBK subframe connectors.
UPR upper and lower control arms

Wheels
Weld wheels Big and little with new tires up front
and New tires in the rear 26inch tall tire.

Other stuff:
The car has a 8pt roll cage just recently put in.
3 cervinis cowl hood.
Monster Tach, with oil pressure gauge and water temp gauge
and nitrous pressure gauge.
New black carpet, racing seats,Brand new B&M ratch shifter.
Cervinins fiber glass hood. 3 Cowl hood
Window tint
Brand new battery.
hood pins.
driver shaft loop
with a fms aluminun driveshaft.
White face gauges

[shawnaj7731]

ttt